Skip to Content

EEPL-CHG-6S6A Battery Charger

4S / 6S LiPo and Li-ion balance charger, 6 A, 230 VAC

EEPL-CHG-6S6A 4S/6S 6 A balance charger with OLED display, balance ports and XT60 output

CAD render

Charge one 4S or 6S drone pack straight from the mains

The EEPL-CHG-6S6A is a bench charger for one 4S (14.8 V) or 6S (22.2 V) LiPo or Li-ion drone pack, powered directly from Indian 230 VAC mains. It charges at 2, 4 or 6 A with constant current, then holds the highest cell at 4.200 V while it balances the pack, and finishes only when every cell is within 10 mV of the others.

The cell count is set in hardware by the balance lead, so a 4S pack never sees a 6S voltage. The display and all battery connections are on the front panel; only the mains inlet is at the rear.

Request Quote Ask About Availability

In prototype. Figures on this page are from specification EEPL-CHG-6S6A-SPEC-01 Rev B and will be confirmed in prototype testing; some may change before release.

Key Performance Metrics

4S / 6S

Cell count

Detected from the balance lead; any other count is refused

6 A

Maximum charge current

2, 4 or 6 A, chosen with one button

10 mV

Cell balance at full

Every cell measured to ±10 mV and balanced to within 10 mV

Core Capabilities

Two independent overcharge layers

Firmware stops the charge at 4.25 V on any cell. A separate hardware comparator disconnects the pack at 26.04 V (6S) or 17.37 V (4S) even if the microcontroller fails.

Balances while it charges

Passive balancing on every cell at about 180 mA, during charge and in a balance-only phase, with cell readings taken while the bleeders are off.

Refuses the wrong pack

2S, 3S or 5S packs, mismatched leads, a cell below 2.5 V or above 4.25 V (including LiHV) are refused with a fault code before charging starts.

Full protection set

Over-current, output short, reversed pack with mains on or off, over-temperature with derating, sensor failure, no start below 0 °C, and a 6-hour safety timer.

Every cell on the display

A 1.3-inch OLED shows pack voltage, current, mAh, temperature and every cell voltage, with the bleeding cells marked, plus plain-text fault codes E01 to E17.

Class II mains design

Single-stage isolated flyback for 180–265 VAC with reinforced insulation (8 mm creepage), designed to IEC 60335-1 and IEC 60335-2-29.

Technical Overview

Input

180–265 VAC, 47–63 Hz, 180 W max

Output

25.2 V (6S) or 16.8 V (4S), 151 W max

Charge method

Precharge, constant current, per-cell CV at 4.200 V, balance

Charge current

2 / 4 / 6 A (±5 %); 0.5 A precharge below 3.0 V per cell

Chemistry

LiPo and Li-ion, 4.20 V per cell (not LiHV or LiFePO4)

Recommended pack

2 to 30 Ah

Balancing

Passive, 160–200 mA per cell, spread at full 10 mV or less

Output connector

XT60, panel mount, front

Balance ports

JST-GH 7-pin (6S), JST-GH 5-pin (4S), JST-XH 7-pin

Display and controls

1.3-inch OLED, one START/STOP button, red and green status LEDs

Cooling

Forced air; full output from 0 to 40 °C

Mains

IEC C8 inlet, 1.5 m cord with Indian 2-pin plug

Dimensions

243 × 161 × 71 mm

Mass

1.2 kg or less (target)

Origin

Designed in India by EEPL

Inside the charger

A single isolated flyback stage feeds the battery side, where the microcontroller, cell measurement and balancing live. The battery switch stays open until a valid pack is detected on both leads, so the XT60 output is dead when nothing is connected.

Every production unit is calibrated before it ships, with cell gains stored and checked; an uncalibrated unit refuses to charge. Each unit is also burned in for one hour at 6 A.

EEPL-CHG-6S6A charger with the cover shown transparent

CAD render, cover shown transparent

Need chargers for your fleet?

Tell us your pack sizes and quantities and we will come back with pricing and availability.

Request Quote